Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
We've come across the article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround directly below on the net and figured it made good sense to relate it with you on my blog.
Installing a bathtub isn't specifically brain surgery, however it does call for solid plumbing, carpentry, and in some cases, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately hard job. If the old tub is conveniently easily accessible, the project can relocate rapidly; if you have to open a wall to get rid of the old tub as well as position the new tub, the task is much harder. In either instance, the project is within a home handyman's skills, although you will need a helper to vacate the old bathtub and set in the new one. Make certain you have actually certified on your own for the job and are comfortable attempting it. Instead of hiring a specialist to take control of a halfway-completed job, it is far better to take into consideration employing one prior to you start. Opportunities are you may need a specialist plumber to make tube connections.
This article will certainly assist you install a new tub in your shower room if you have actually already purchased a new tub and do not require to change the setup of your previous supply of water pipelines.
Your devices and material list need to comprise the following:
Getting ready for the Installment
To start with, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now be ready to be fitted in its final setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The process of removing the existing faucets can be rather troublesome because of the restricted accessibility that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the continuing to be water that will come from the pipes. When the supply pipes have actually been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before going on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Bathtub
Using both wood boards under its feet, put the bathtub in the called for placement. The wooden boards are valuable in evenly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The following goal is to make certain that the tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bathtub until the spirit level checks out degree.
To set up faucets, fit all-time low of the outermost versatile faucet adapter to the proper supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Turn on the water system as well as check all joints and brand-new pipework for leaks and also tighten them if necessary. Load the tub and additionally examine the overflow electrical outlet and the regular outlet for leakages.
Finally, deal with the bath paneling as explained in the producer's instruction manual. Tiling and also securing around the bathtub needs to wait until the tub has actually been used at the very least once as this will settle it right into its last position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin guaranteeing that the washing machines are in location in between the faucet and also the sink. Protect the tap in position with the manufacturer given backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet adapters. The previous type ought to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture a rigid seal, creating the water to pass through the wall surface between the bathroom and also the tiling, bring about difficulties with moisture as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your components and fittings. They are sold in tubes and cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of soaked paper or soft rope. Remember to constantly fill the bath tub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can split rather very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally quickly offered on the market. It is recommended to fit the tiles using waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic reader on How to Install a Bathtub Yourself, I imagined sharing that piece of content was a good idea. Enjoyed our content? Please share it. Help another person find it. Thanks a bunch for your time. Come back soon.
Professional touch awaits. Report this page